top of page
RUTANPUMP submersible water pump product image illustrating the source-pump stage of a two-stage system

Two-Stage Solar Pump System: Sizing Across a Break Tank

作家相片: Tony Wang
Tony Wang
11月8日
讀畢需時 5 分鐘

In a two-stage solar pump system with an atmospheric break tank, size the source pump and the downstream booster separately. The first pump fills the tank against the source-to-tank head. The second serves the outlet against its own lift, friction and required pressure. The tank separates the hydraulic duties, but its water balance still links their operating schedules.


RUTANPUMP submersible water pump product image illustrating the source-pump stage of a two-stage system

This approach is useful where the source can deliver water steadily but the users need a higher short-term flow, or where a single pressure zone would make the whole transfer line harder to design and maintain. It does not automatically save energy, increase available source water, or guarantee service after sunset. A two-stage proposal must close three checks: both pump duties and the usable water balance between them.


Draw the hydraulic boundary before choosing pumps


Mark the lowest credible pumping water level at the source, the tank fill outlet, the permitted range of water levels inside the tank, and the least favorable downstream outlet. Reference these elevations to one datum. Show the line and valve arrangement on each side of the tank. If the incoming line terminates at an air gap, use the actual discharge point and outlet conditions in the first calculation; do not automatically use the bottom or middle of the tank.


On the downstream side, start from the minimum usable water level for the low-inlet-head check. A lower tank water surface increases the head the booster must add to reach a given delivery condition and can reduce available suction head. A tank mounted above a pump does not by itself establish adequate inlet conditions. Include the suction line, fittings, water temperature, intake arrangement and the manufacturer's limits. The tank bottom is not necessarily an allowable operating level.


Grundfos's break tank overview describes how break tanks separate pressure zones in boosting systems. Use it to understand the arrangement, not as approval of a specific tank, air gap or booster. A site designer must address local backflow, sanitation, overflow and structural requirements independently.


Select the source pump for filling duty


Build a source-to-tank system curve using the expected pumping water levels and the fill line's flow-dependent losses. Then verify the selected pump's delivery under the solar and source conditions that matter. The nominal curve at a single speed is not a daily production estimate. The borehole yield, seasonal drawdown, PV operating window and controller limitations still govern how much can reach the tank.


Consider the easiest duty as well as the hardest one. At a higher source water level, an otherwise suitable pump can move more water than the source or fill connection can sustain. In a low-water condition, it may supply fewer cubic metres per day than the project requires. Use the supplier's permitted operating envelope rather than assuming every flow below the nameplate maximum is acceptable. The RUTANPUMP borehole installation-depth guide explains why source water level, pump setting and submergence are distinct inputs.


Select the booster for downstream service


Start with the peak approved downstream service case and the minimum residual pressure at the critical outlet. Add elevation difference and losses for the active route, including dirty-filter conditions where the filter supplier provides a valid allowance. Check a low-demand operating case too: excessive pressure or repeated short cycling can be a problem even if the selected pump meets peak demand. Pressure rating and surge assessment are separate from the normal operating head.


The U.S. Department of Energy variable-speed pumping guide explains how the pump curve and system curve determine the operating point. Apply that principle independently to each side. Do not add two catalogue head values and call the result a combined curve: these pumps do not share one continuous pressurized path and can operate at different flow rates. A direct series-pump system without an atmospheric break is a different design.


Worked example: delivery rate is not refill rate


The following values are hypothetical, not RUTANPUMP ratings or a project recommendation. Suppose a solar source pump can deliver an average of 4 cubic metres per hour for five useful hours under a specified design condition. Its projected daily fill is 20 cubic metres. If the source-to-fill-outlet elevation difference is 26 metres and the fill line loses 5 metres of head at that flow, the representative fill duty is 4 cubic metres per hour at 31 metres. This simplified example still needs a real pump curve and source-yield check.


Suppose the downstream system needs 8 cubic metres per hour for a two-hour service block. At minimum tank level, assume 10 metres of static lift, 6 metres of line and fitting loss, and a required outlet pressure equivalent to 12 metres of water head. The representative booster duty is 8 cubic metres per hour at 28 metres. The two-hour block withdraws 16 cubic metres. If the source pump contributes nothing during that block, the usable water above the permitted minimum must already cover all 16 cubic metres before separate reserve or uncertainty allowances.


If the source delivers 4 cubic metres per hour throughout both hours, only 8 cubic metres of stored water are used during that overlap. That result is not a guaranteed storage saving: the overlap may disappear during low sunlight or a source stop. Check both the expected overlap and an approved no-overlap case. Do not assume a tank's nominal volume is usable volume; subtract the inaccessible water below the permitted operating level and keep required reserve and freeboard separate.


Two-stage selection worksheet


  • Source pump duty: record source water levels, proposed flow, fill outlet elevation, pipe losses, sustainable source rate, available PV conditions and the exact curve revision.

  • Booster duty: record minimum tank water level, critical outlet elevation, required outlet pressure, simultaneous flow, distribution losses and booster inlet conditions.

  • Tank operating band: record high stop, refill demand, minimum usable level, booster inhibit level and the capacity between those levels using the actual tank geometry.

  • Water balance: list inflow and withdrawal for each time block, including morning startup, peak service, low sunlight and planned shutdown. Carry the ending tank volume into the next block.

  • Power availability: identify the source and controller for each pump, especially if downstream delivery is required outside useful sunlight. Stored water alone cannot power an electric booster.

  • Acceptance cases: agree on the equipment states and measurements for tank-low inhibit, refill recovery, peak demand and loss of source input. Ask the responsible designer to approve each case and its safe test method.


Review the RUTANPUMP solar pump and tank sizing guide for the overall daily-volume calculation. For two-stage designs, retain the time-block balance as an additional check rather than replacing it with a daily total.


Frequently asked questions


Can the booster flow be higher than the solar refill flow?


Yes, for a limited period if the tank has enough usable water and the source can replenish the withdrawal over the approved schedule. A sustained deficit will eventually empty the usable tank volume.


Does the tank guarantee outlet pressure after sunset?


No. It stores water, not electrical power. After-sunset service needs an approved booster supply or a separately verified gravity delivery arrangement.


Can I select the booster with the tank full?


Check that state, but also evaluate minimum usable tank level. It can be the more demanding inlet and delivery case. Use the actual water level and inlet losses, not simply the tank's elevation on a drawing.


Request a two-stage selection review


Send RUTANPUMP / Wenling Jingzhan Mechanical & Electrical Co., Ltd. your elevation sketch, both duty points, tank level band and time-block water balance through the RUTANPUMP contact page. Email sales@rutanpump.com; WhatsApp/WeChat +86 18267835331; telephone +86 (0576) 86322398. Request a curve and operating limits for the exact pump proposed for each stage. A product image illustrates the equipment category, not approval of the worked example.

 
 
 

留言


bottom of page