top of page
RUTANPUMP submersible water pump product image illustrating the source pump in a solar-fed irrigation system

Solar Pump Filter Backwash Sizing: Check Flow, Pressure and Reserve

作家相片: Tony Wang
Tony Wang
11月10日
讀畢需時 5 分鐘

Solar pump filter backwash sizing starts with a separate hydraulic duty for cleaning the filter. An irrigation pump that delivers the right volume to the field over a day may still fail to provide the required wash flow and pressure for several minutes. Check the wash duty at the filter manufacturer's specified reference point, then check whether the pump, source or dedicated reserve can sustain the full sequence.


RUTANPUMP submersible water pump product image illustrating the source pump in a solar-fed irrigation system

This worksheet is for solar-fed irrigation projects that already have a candidate filter and are comparing ways to supply its backwash. It does not select the filter medium or prescribe control settings. If the filter itself is not selected, start with the RUTANPUMP drip irrigation filtration guide, which covers water quality, filter types and ordinary filtration losses.


Translate the filter specification into two operating cases


First write down normal filtration flow and the minimum pressure needed by the critical irrigation zone. State what filter differential pressure is assumed just before cleaning. Then make a separate row for wash mode. Identify which chamber cleans, which chambers or supply line provide clean wash water, what the irrigated zones do during cleaning, and where the waste water exits. Draw arrows for both cases; a normal-flow diagram can hide a valve path that matters only during washing.


Ask the filter supplier to identify the minimum wash pressure, the exact point where it is measured and the permitted range of wash flow. A stated pressure at the wash inlet is not interchangeable with a gauge reading at the pump discharge. Differential pressure across a dirty filter may trigger a cycle, but that trigger is not the pressure available to drive the wash. Penn State Extension's drip irrigation guidance describes why media cleaning depends on the appropriate reverse flow. Use the selected filter data rather than borrowing a rate from a different tank or medium.


Check whether the supplier assumes a free waste outlet or allows a specified backpressure. A long rising waste line or a receiving tank that floods its outlet can change the wash conditions. Do not assume that a larger pump alone remedies a restricted drain. The responsible designer should review disposal, operating pressure and the allowed discharge routing independently of the water-volume calculation.


Compare both duties with the available solar operating envelope


If irrigation continues while the filter washes, calculate the combined flow where branches share a header. At that combined flow, recalculate losses in the common line. For each branch, determine whether the common supply can maintain the required pressure at the branch's reference point. Do not simply add the two pressure requirements. If the proposed arrangement pauses irrigation, evaluate the wash-only duty and confirm the resulting interruption is acceptable for the field schedule.


For a direct-solar installation, use pump performance at the available operating speed or power, not just the full-power curve. A weak-sun period can be long enough to trigger a wash request but too weak for the pump to complete it. Confirm how the approved controls distinguish a wash request from permission to begin, and what happens if pressure drops during the cycle. Do not defeat cleaning limits or defer cleaning indefinitely just to preserve field flow. The filter supplier should specify the permitted response to an incomplete sequence.


The Netafim SandStorm initial-operation reference illustrates equipment-specific checks on pressure difference and completed wash sequencing. It is not a source of universal settings. Use it to understand why a completed timer, a recovered pressure difference and actual hydraulic delivery are separate pieces of evidence.


Worked example: a short wash can dominate peak pump demand


The values below are hypothetical and are not filter recommendations or RUTANPUMP ratings. Assume a supplier specifies 6 cubic metres per hour of clean wash flow at its stated inlet reference, for 90 seconds per chamber. Assume three chambers wash sequentially, with no overlap. The theoretical wash withdrawal is 6 multiplied by 90 divided by 3,600, or 0.15 cubic metres per chamber. A complete three-chamber sequence therefore uses 0.45 cubic metres before any separate rinse, purge or allowance.


Suppose irrigation normally draws 10 cubic metres per hour and the project intends to maintain that entire flow during washing. If both draws come from the same upstream source, the shared section must support 16 cubic metres per hour while one chamber washes. The pump must satisfy that flow at the head required by the controlling branch, including the shared-line loss at the combined flow. If the wash supplier requires 200 kilopascals at the reference point and the upstream route consumes an additional equivalent 40 kilopascals at that operating condition, the hypothetical supply requirement for that branch is 240 kilopascals at the defined upstream point. The irrigation branch still needs its own pressure check.


The 0.45 cubic metres of wash water and the 16 cubic metres per hour peak supply are not competing answers. One is volume for a sequence; the other is instantaneous duty. A reserve tank can cover the volume if it contains enough usable clean water and the delivery arrangement provides the wash pressure. A tank without adequate gravity head or a verified booster does not satisfy the pressure check. If it has a booster, confirm power availability during the intended wash window.


Backwash duty and reserve worksheet


  • Filtration case: record zone flow, required outlet pressure, filter differential pressure at the intended cleaning trigger, and available source conditions.

  • Wash case: record the supplier's wash-flow range, minimum pressure and reference point, maximum waste backpressure, chamber sequence and timed steps.

  • Common supply: state whether irrigation continues, pauses or changes zones; calculate shared flow and loss for each allowed operating state.

  • Reserve: total the actual timed wash and rinse steps, then verify usable volume above the approved minimum operating level, replenishment time and clean-water source.

  • Commissioning record: record timestamped inlet and outlet pressures, wash flow or accepted measurement proxy, valve sequence, cycle completion, and comparable pre- and post-wash differential pressures.


Compare differential pressure before and after cleaning at comparable filtration flow. A lower reading after a cycle may merely reflect lower irrigation flow if solar input or the zone state changed. Agree with the supplier on the conditions for comparison and what evidence is acceptable. For a separate clean-water tank and booster, the RUTANPUMP two-stage break tank guide shows how to treat refill and downstream delivery as different duties.


Frequently asked questions


Can I size backwash from daily irrigation volume?


No. Daily volume helps with water supply planning, but washing also requires an instantaneous flow and pressure at the filter's specified point.


Does an automatic backwash command guarantee the filter is clean?


No. Confirm the actual sequence, available wash conditions and the resulting differential pressure at comparable filtration flow, following the supplier's acceptance criteria.


Can I use the full nameplate tank volume as wash reserve?


No. Use the volume available above the approved operating minimum, after accounting for any other demand that can draw from the same tank.


Request a pump duty review


Send the completed worksheet and filter documentation to RUTANPUMP / Wenling Jingzhan Mechanical & Electrical Co., Ltd. via the RUTANPUMP contact page or sales@rutanpump.com. WhatsApp/WeChat: +86 18267835331. Telephone: +86 (0576) 86322398. Ask for the pump curve and allowable operating range for both cases, not a single wattage-based recommendation. The product image shows a source-pump category, not an installed backwash system.

 
 
 

留言


bottom of page